Gas booster pump is a commonly used device used to increase gas pressure and provide high-pressure gas supply. The following are the steps to use the gas booster pump:

準備工作：

preparation:

確保氣體增壓泵的工作環境通風良好，沒有易燃易爆物品。

Ensure that the working environment of the gas booster pump is well ventilated and free from flammable and explosive materials.

檢查氣體增壓泵的外觀和連接部件，確保無損壞或松動現象。

Check the appearance and connecting components of the gas booster pump to ensure there is no damage or looseness.

確保氣體增壓泵的電源接線正確并接地良好。

Ensure that the power wiring of the gas booster pump is correct and well grounded.

連接氣源：

Connect the air source:

將氣源管路與氣體增壓泵的進氣口連接，并確保連接牢固。

Connect the gas source pipeline to the inlet of the gas booster pump and ensure that the connection is secure.

如果需要使用過濾器或調壓閥等附件，可以在進氣口處進行連接。

If accessories such as filters or pressure regulating valves are needed, they can be connected at the air inlet.

連接出氣管路：

Connect the air outlet pipeline:

將出氣管路與氣體增壓泵的出氣口連接，并確保連接牢固。

Connect the outlet pipeline to the outlet of the gas booster pump and ensure that the connection is secure.

如果需要調節出氣壓力，可以在出氣口處安裝調壓閥，并根據需要進行調整。

If the outlet pressure needs to be adjusted, a pressure regulating valve can be installed at the outlet and adjusted as needed.

啟動氣體增壓泵：

Start the gas booster pump:

打開氣體增壓泵的電源開關，確認電源正常供電。

Turn on the power switch of the gas booster pump and confirm that the power supply is normal.

按下啟動按鈕或旋轉開關，啟動氣體增壓泵。

Press the start button or rotary switch to start the gas booster pump.

留意氣體增壓泵的工作狀態，確保其正常運轉。

Pay attention to the working status of the gas booster pump to ensure its normal operation.

調節壓力：

Adjusting pressure:

如果需要調節出氣壓力，可以根據需要使用調壓閥進行調整。

If the outlet pressure needs to be adjusted, a pressure regulating valve can be used as needed for adjustment.

根據具體要求，逐步調節調壓閥，使出氣壓力達到所需值，并確保穩定。

According to specific requirements, gradually adjust the pressure regulating valve to achieve the required outlet pressure and ensure stability.

停止使用：

Discontinued use:

當不再需要使用氣體增壓泵時，先關閉氣源，切斷氣體供應。

When the gas booster pump is no longer needed, first turn off the gas source and cut off the gas supply.

關閉氣體增壓泵的電源開關，停止其工作。

Turn off the power switch of the gas booster pump and stop its operation.

斷開氣源管路和出氣管路的連接，確保安全。

Disconnect the air source pipeline and outlet pipeline to ensure safety.

請注意，以上步驟僅為一般性指導，具體的操作步驟和注意事項應根據氣體增壓泵的型號和使用說明進行操作，確保安全和正確使用。在使用氣體增壓泵之前，建議仔細閱讀設備的操作手冊，并遵循生產廠家提供的使用指導

Please note that the above steps are only general guidance. The specific operating steps and precautions should be based on the model and instructions of the gas booster pump to ensure safe and correct use. Before using the gas booster pump, it is recommended to carefully read the equipment's operating manual and follow the instructions provided by the manufacturer for use