不同的增壓泵安裝方法要求也不同拿我們的氣液增壓泵舉個例子；
Different installation methods for booster pumps also require different requirements. Take our gas-liquid booster pump as an example;
氣液增壓泵要求的驅動氣壓范圍：1bar≤驅動氣壓≤8.3bar；
The required driving pressure range for the gas-liquid booster pump: 1 bar ≤ driving pressure ≤ 8.3 bar;
它對工作環境也是有要求的：要求無塵（允許微粒為40μm、無腐蝕、環境溫度0-60°C）；
It also has requirements for the working environment: dust-free (maximum allowable particle size is 40 μ m. No corrosion, ambient temperature 0-60 ° C);
驅動氣體接入：在標注有驅動空氣接口（端口螺紋安裝尺寸有備注），接入驅動和預壓縮介質，建議配置過濾器裝置精度滿足我們要求，驅動進氣配置油霧器對泵體本身起到潤滑作用（油霧器建議添加VG32的透平油，其它油會加快密封件的老化），低溫環境請添加抗低溫潤滑油。
Drive gas connection: When the drive air interface is marked (with remarks on the installation size of the port thread), it is recommended to connect the drive and pre compressed media. It is recommended to configure a filter device with accuracy that meets our requirements. The drive intake is equipped with an oil mist device to lubricate the pump body itself (it is recommended to add VG32 turbine oil to the oil mist device, as other oils will accelerate the aging of the seals). In low-temperature environments, please add low-temperature resistant lubricating oil.
介質種類：增壓介質可以是液壓油、純水、液態CO2等，常規增壓泵介質不可是腐蝕性、氧化性易燃易爆液體，如硝酸鹽等。
Medium type: The boosting medium can be hydraulic oil, pure water, liquid CO2, etc. The conventional booster pump medium cannot be corrosive, oxidizing, flammable and explosive liquids, such as nitrates.
氣液增壓泵.jpg
Gas-liquid booster pump.jpg
低壓介質接入：在標注有入口接口（端口螺紋安裝尺寸有備注），接入增壓介質，介質純凈度要求為NAS1638-10級，建議配置過濾器裝置精度滿足我們要求,嚴禁介質中混入鐵渣焊渣、粉塵等固體顆粒，液壓油等循環利用的介質請定期對其更換或過濾。
Low pressure medium access: When the inlet interface is marked (with remarks on the installation size of the port thread), the pressurized medium is connected. The minimum purity requirement for the medium is NAS1638-10 level. It is recommended to configure a filter device with accuracy that meets our requirements. It is strictly prohibited to mix solid particles such as iron slag, welding slag, dust, and hydraulic oil in the medium. Please replace or filter it regularly.
溫度要求：常規增壓泵，驅動氣體和氣缸工作時溫度為-20~80℃，超出此范圍必須停機，溫度正常方可開機。耐高溫產品規定溫度執行。
Temperature requirements: For conventional booster pumps, the temperature of the driving gas and cylinder during operation is -20~80 ℃. If the temperature exceeds this range, the pump must be shut down and can only be started if the temperature is normal. The specified temperature for high-temperature products shall be implemented.
管路要求：根據泵的輸出壓力，必須選擇能承受泵輸出壓力的管路。
Pipeline requirements: Based on the output pressure of the pump, a pipeline that can withstand the maximum output pressure of the pump must be selected.
固定方式：每臺增壓泵都配有兩個L型腳架，根據腳架上的開孔尺寸進行安裝。
Fixing method: Each booster pump is equipped with two L-shaped legs, which are installed according to the size of the holes on the legs.
啟動：
Start:
1.確保增壓泵固定牢靠。
1. Ensure that the booster pump is securely fixed.
2.確保所有的接口都緊固連接而且原件安裝到位。
2. Ensure that all interfaces are securely connected and the components are installed in place.
3..調節減壓閥，將氣壓調到0psi。
3. Adjust the pressure reducing valve to set the air pressure to 0psi.
4.打開進氣開關，慢慢調大減壓閥直到泵啟動（正常情況下泵的啟動壓力在15~20psi）,繼續調節并觀察高壓壓力表，達到您需要的壓力。
4. Turn on the intake switch, slowly increase the pressure reducing valve until the pump starts (under normal circumstances, the starting pressure of the pump is 15-20psi), continue to adjust and observe the high-pressure pressure gauge to reach the pressure you need.
This article is dedicated to the friendship of gas booster pumps. For more relevant knowledge, please click on: http://www.margilowry.com Sincere attitude. We will provide you with comprehensive services. We will gradually contribute more relevant knowledge to everyone. Stay tuned
